Minwax Pre-stain Wood Conditioner - 1 Qt
SKU:
545988
UPC:
027426615007
$22.99
Minwax Pre-Stain Wood Conditioner Prepares Bare Wood For Staining. It Penetrates The Grain Of The Wood To Promote Uniform Acceptance Of Oil-based Stains.
Features
- Treating The Surface With Pre-Stain Wood Conditioner Helps Prevent Streaks And Blotches By Evening Out The Absorption Of Oil-based Stains
- It Can Be Applied Over Any Wood But Is Especially Necessary When Working With Soft Or Porous Woods Like Pine, Alder, Birch, And Maple
- Normally 1 Coat But Additional Coats May Be Applied On Highly Absorbent Woods
Directions
Surface Preparation:
- Before Staining, Apply Minwax Pre-Stain Wood Conditioner On Clean, Raw Wood, Using A Brush Or Cloth
- Allow To Penetrate For 5 To 15 Minutes, Then Remove Any Excess With Clean, Dry Cloth
- Apply Stain Within Two Hours Of Application Of Pre-Stain Wood Conditioner. For Best Results, Stain With Minwax Wood Finish, Minwax Gel Stain, Or Minwax PolyShades
Specifications
- Size: 1 Qt
- Application Tool: Cloth Or Brush
- Recoat: 15 Min - 2 Hr
- Dry Time: 15 Min
- Cleanup: Mineral Spirits Or Paint Thinner, following Manufacturer’s Safety Instructions
- Coverage: 125 Sq. Ft.
- Number Of Coat: 1 Coat
- Recommended Uses: On Soft Or Hardwoods Before Using Oil-based Wood Stains
- Certified: Conforms To ASTM D-4236.Â
- Coverage: 125 Square Feet Per Quart
- Cautions: Contains Aliphatic Hydrocarbons, Contents Are Combustible. Keep Away From Heat And Open Flame
- Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.
Minwax Pre-Stain Wood Conditioner Prepares Bare Wood For Staining. It Penetrates The Grain Of The Wood To Promote Uniform Acceptance Of Oil-based Stains.
Features
- Treating The Surface With Pre-Stain Wood Conditioner Helps Prevent Streaks And Blotches By Evening Out The Absorption Of Oil-based Stains
- It Can Be Applied Over Any Wood But Is Especially Necessary When Working With Soft Or Porous Woods Like Pine, Alder, Birch, And Maple
- Normally 1 Coat But Additional Coats May Be Applied On Highly Absorbent Woods
Directions
Surface Preparation:
- Before Staining, Apply Minwax Pre-Stain Wood Conditioner On Clean, Raw Wood, Using A Brush Or Cloth
- Allow To Penetrate For 5 To 15 Minutes, Then Remove Any Excess With Clean, Dry Cloth
- Apply Stain Within Two Hours Of Application Of Pre-Stain Wood Conditioner. For Best Results, Stain With Minwax Wood Finish, Minwax Gel Stain, Or Minwax PolyShades
Specifications
- Size: 1 Qt
- Application Tool: Cloth Or Brush
- Recoat: 15 Min - 2 Hr
- Dry Time: 15 Min
- Cleanup: Mineral Spirits Or Paint Thinner, following Manufacturer’s Safety Instructions
- Coverage: 125 Sq. Ft.
- Number Of Coat: 1 Coat
- Recommended Uses: On Soft Or Hardwoods Before Using Oil-based Wood Stains
- Certified: Conforms To ASTM D-4236.Â
- Coverage: 125 Square Feet Per Quart
- Cautions: Contains Aliphatic Hydrocarbons, Contents Are Combustible. Keep Away From Heat And Open Flame
- Warning: This Product Contains Chemicals Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.