null Skip to main content
Zoom the image with the mouse

Rust-oleum Professional High-performance Protective Enamel Paint - Gloss Black - 1 Gal

No reviews yet
SKU: 355172
UPC: 020066777944
$54.99

Provide A Tough, Attractive Coating That Withstands Heavy-duty Environments With Rust-Oleum Professional High-Performance Protective Enamel. This Commercial-quality Finish Maintains Consistent, Corrosion-resistant Color Despite The Elements.

Rust-Oleum Professional DTM Alkyd Enamels Are Oilmodified Alkyds With Excellent Rust Prevention When Applied Directly To Metal. They Also Offer Excellent Coverage, Chip Resistance And Color Retention.

Features
  • Indoor/outdoor Use
  • Durable, Corrosion-resistant
Application

Mix Thoroughly To Ensure Any Settled Pigment Is Redispersed Before Using. Thin Material, Only If Necessary, With Acetone. For Brush Or Roller, Thinning Is Not Normally Required. For Air Spray, Thin Up To 1-1/2 To 2 Pt Per Gal. Do Not Thin With Gasoline, Lacquer Thinner, Turpentine, Etc. For Airless Spray, Thinning Is Not Normally Required. Apply With A Good Quality Brush, Roller Or Spray Gun.

Brush: Use Light Even Strokes Excessive Brushing Reduces Film Thickness And Protection.

Roller: The Rougher The Surface, The Longer The Roller Nap Should Be. Cover Approximately One Square Yard At A Time. Roll Away From The Previously Coated Area And Work Back O It For A Uniform Appearance. Use A Brush On Crevices And Sharp Edges.

Spray Gun: Follow Spray Gun Directions Carefully. Always Keep The Gun Ten To Twelve Inches From The Surface And In Motion While Spraying.

Dry And Recoat Times

Dry And Recoat Times Are Based On 70°F (21°C) And 50% Relative Humidity. Allow More Time At Cooler Temperatures. Dries To The Touch In 2-4 Hours, To Handle In 5-9 Hours And Is Fully Dry After 24 Hours. Recoat After 24 Hours. Do Not Apply Clear Enamel Over Stops Rust Bright Coat Finish Or Aluminum Finish.

Cleanup

Clean Brush And Tools With Mineral Spirits.

Painting Conditions

Apply Only When Air And Surface Temperatures Are Between 32-90ºF (0-38ºC) And Humidity Is Below 85% To Ensure Proper Drying. Do Not Apply To Surfaces That, When Heated, Exceed 200ºF (93ºC) Or Galvanized Metal. Professional DTM Alkyd Enamels Can Be Used Over Most Latex Or Oil Paints. Professional DTM Alkyd Enamels And Primers Are Not Recommended For Water Immersion.

Surface Preparation

Clean Surface With Soap And Water, Rinse And Let Dry. Remove Loose Paint And Rust With A Wire Brush Or Sandpaper. Lightly Sand Glossy Surfaces.

Warning

If You Scrape, Sand Or Remove Old Paint From Any Surface, You May Release Lead Paint Dust. Lead Is Toxic. Exposure To Lead Dust Can Cause Serious Illness, Such As Brain Damage; Especially In Children. Pregnant Women Should Also Avoid Exposure. Wear A NIOSH Approved Respirator To Control Lead Exposure. Clean Up Carefully With A HEPA Vacuum And A Wet Mop.

Specifications
  • Color: Gloss Black
  • Size: 1 Gal
  • Resin Type: Modified Alkyd
  • Solvents: Aliphatic Hydrocarbons
  • Dry Heat Resistance: 212°F (100°C)
  • Flash Point: 104°F (93°C)

Safety Data Sheet.pdf

 

Provide A Tough, Attractive Coating That Withstands Heavy-duty Environments With Rust-Oleum Professional High-Performance Protective Enamel. This Commercial-quality Finish Maintains Consistent, Corrosion-resistant Color Despite The Elements.

Rust-Oleum Professional DTM Alkyd Enamels Are Oilmodified Alkyds With Excellent Rust Prevention When Applied Directly To Metal. They Also Offer Excellent Coverage, Chip Resistance And Color Retention.

Features
  • Indoor/outdoor Use
  • Durable, Corrosion-resistant
Application

Mix Thoroughly To Ensure Any Settled Pigment Is Redispersed Before Using. Thin Material, Only If Necessary, With Acetone. For Brush Or Roller, Thinning Is Not Normally Required. For Air Spray, Thin Up To 1-1/2 To 2 Pt Per Gal. Do Not Thin With Gasoline, Lacquer Thinner, Turpentine, Etc. For Airless Spray, Thinning Is Not Normally Required. Apply With A Good Quality Brush, Roller Or Spray Gun.

Brush: Use Light Even Strokes Excessive Brushing Reduces Film Thickness And Protection.

Roller: The Rougher The Surface, The Longer The Roller Nap Should Be. Cover Approximately One Square Yard At A Time. Roll Away From The Previously Coated Area And Work Back O It For A Uniform Appearance. Use A Brush On Crevices And Sharp Edges.

Spray Gun: Follow Spray Gun Directions Carefully. Always Keep The Gun Ten To Twelve Inches From The Surface And In Motion While Spraying.

Dry And Recoat Times

Dry And Recoat Times Are Based On 70°F (21°C) And 50% Relative Humidity. Allow More Time At Cooler Temperatures. Dries To The Touch In 2-4 Hours, To Handle In 5-9 Hours And Is Fully Dry After 24 Hours. Recoat After 24 Hours. Do Not Apply Clear Enamel Over Stops Rust Bright Coat Finish Or Aluminum Finish.

Cleanup

Clean Brush And Tools With Mineral Spirits.

Painting Conditions

Apply Only When Air And Surface Temperatures Are Between 32-90ºF (0-38ºC) And Humidity Is Below 85% To Ensure Proper Drying. Do Not Apply To Surfaces That, When Heated, Exceed 200ºF (93ºC) Or Galvanized Metal. Professional DTM Alkyd Enamels Can Be Used Over Most Latex Or Oil Paints. Professional DTM Alkyd Enamels And Primers Are Not Recommended For Water Immersion.

Surface Preparation

Clean Surface With Soap And Water, Rinse And Let Dry. Remove Loose Paint And Rust With A Wire Brush Or Sandpaper. Lightly Sand Glossy Surfaces.

Warning

If You Scrape, Sand Or Remove Old Paint From Any Surface, You May Release Lead Paint Dust. Lead Is Toxic. Exposure To Lead Dust Can Cause Serious Illness, Such As Brain Damage; Especially In Children. Pregnant Women Should Also Avoid Exposure. Wear A NIOSH Approved Respirator To Control Lead Exposure. Clean Up Carefully With A HEPA Vacuum And A Wet Mop.

Specifications
  • Color: Gloss Black
  • Size: 1 Gal
  • Resin Type: Modified Alkyd
  • Solvents: Aliphatic Hydrocarbons
  • Dry Heat Resistance: 212°F (100°C)
  • Flash Point: 104°F (93°C)

Safety Data Sheet.pdf

Customer Reviews

This product hasn't received any reviews yet. Be the first to review this product!