Liquid Nails Interior Projects Construction Light Tan Adhesive - 10 oz

  • Strong durable bond
  • Bonds most common building materials
  • Bond remains flexible
Availability: In stock


Liquid Nails Project Construction Adhesive LN-601 is a proven high-quality, waterproof adhesive that creates a strong durable bond that remains flexible, bridges gaps up to 3/8" and offers up to 10 minutes working time.

Surface Preparation

Make sure that all surfaces are clean, dry, and structurally sound before the product is applied. Cut and pre-fit materials prior to installation.


Insert Liquid Nails cartridge into a standard caulking gun. Cut nozzle at 45° angle to desired bead size marked on the nozzle. Puncture inner seal with nail or wire.

Bonding Paneling to Furring Strips or Studs: Apply a zigzag 1/4" (.64 cm) bead of adhesive to each strip or stud to be covered by material. Position paneling so edges meet at stud center. Only severely warped materials will require finishing nails at the top and bottom.

Bonding Panels, Corkboard, etc. to Flat Surfaces: Apply 1/4" (.64 cm) zigzag vertical adhesive bead a maximum of 12" (30 cm) apart, within 1-1/2" (3 cm) of all edges.

Quick-Bond Method: Press materials firmly into place and pull away for 3 to 5 minutes, then press back into place.

Note: One surface must be porous.

Clean Up

Use mineral spirits or an adhesive remover.


Contains organic solvents which may cause adverse effects to the environment if disposed of improperly. Place empty containers in normal refuse for disposal. Contact your sanitation department or household hazardous waste coordinator for information concerning possible re-use or disposal of unused solvent-containing adhesives and/or sealants.

  • Bonds most common building materials
  • Strong durable bond
  • Bond remains flexible
  • Bridge gaps up to 3/8"
Recommended For
  • Plywood
  • Paneling
  • Molding
  • Furring strips
  • Ceramic fixtures
  • Corkboard
  • Hardboard
  • Drywall
Not Recommended For
  • Finished flooring
  • Subfloors
  • Underlayment
  • Mirrors
  • Ceiling tiles
  • Marble
  • Granite
  • Synthetic marble and granite
  • Size: 10 oz
  • Base: Synthetic rubber and resin
  • Type: Solvent elastomeric adhesive
  • Color: Light tan
  • Appearance: Smooth paste
  • Application Temperature: 20°F–100°F(-7°C–38°C)
  • Service Temperature: -20°F–140°F(-29°C–60°C)
  • Recommended Storage Temperature: 40°F to 100°F (4°C to 38°C)
  • Adhesion: Excellent to all common building materials
  • Consistency: Non-sag
  • Bridging Ability: Excellent; bridges gaps to 3/8" (1 cm)
  • Extrudability: Very good
  • Shear Strength: 24 hours – 250 psi, 48 hours – 350 psi, 7 days – Exceeds 400 psi
  • Durability: Very good; estimated to exceed 20 years
  • Flexibility: Very good
  • Water Resistance: Very good
  • Aging: Very good after accelerated aging cycle
  • Freeze-Thaw Stable: Does not freeze
  • Weight Per Gal: 9.8 lb (1.17 kg/gal)
  • Viscosity: 220,000 CPS
  • Volatiles: 35%
  • Solids: 65%
  • Flammability: Extremely flammable; non-flammable when dry
  • Flash Point: 1°F (-17°C)
  • Coverage: 30 lineal ft. using 1/4" bead for 10 fl.oz
  • VOC: < 40% by wt. (404 g/L)
  • Staining: May stain real or cultured marble & granite
  • Odor: Very slight solvent odor
  • Working Time: Up to 10 min
  • Minimum Cure Time: 24 hr
  • Certifications: ASTM C-557
  • Warranty: Limited Warranty


Write Your Own Review
You're reviewing:Liquid Nails Interior Projects Construction Light Tan Adhesive - 10 oz
Your Rating